FREE Standard Shipping*
Read Featured Reviews From Actual Customers Read All Reviews
Boost your bars at home or in the office.
The Home 10K Plus signal booster from HiBoost is the next generation state of the art 2G, 3G and 4G LTE cell phone signal booster. Now with HiBoost's built-in indoor panel antenna and the HiBoost app you can remotely monitor and troubleshoot your device using HiBoost's Signal Supervisor app.
With the app, you can receive notifications when your booster is running at less than optimal performance or when you need to make adjustments to the output power of the booster. From the app you can also make the recommended adjustments to bring your booster back to peak performance.
With up to +68 dB gain of amplification, it greatly enhances 3G & 4G LTE cell service for all your wireless devices (smartphones, notebooks, hotspots, etc.) on any US carrier indoors up to 10,000 sq ft.
Never drop a call again. Stop waiting for loading screens. No more searching for reception. Get faster internet & updates on your apps. Send emails and text messages with zero delay. Stream video & audio with little to no buffering.
HiBoost is the reliable name in industrial & commercial solutions. When you need coverage, Hiboost has you covered.
- Boosts 3G & 4G LTE for any home or office up to 10,000 sq ft. (depends on configuration)
- Works for all phones & cellular devices, all US & Canadian carriers.
- No monthly fees, no need to be connected to wifi, it just works.
- Remote control capability enabled via the HiBoost app
- For the large home/office size (4,000 to 10,000 sq. ft).
- Great for: large homes, offices and cabins.
- Not recommended for: needing whole building coverage above 10,000 sq. ft.
- HiBoost Home 10K Plus Amplifier w/ Built-In Panel Antenna
- Outside Yagi Antenna
- 50 ft HiBoost200 Cable
- Indoor Panel Antenna (Home 10K Plus Pro Only)
- Power Supply
| HiBoost Home 10K Plus | |
|---|---|
| SKU |
F15GI-5S-BTW - Home 10K Plus F15GI-5S-PRO - Home 10K Plus Pro |
| Working Bands | 698-716 MHz 776-787 MHz 824-849 MHz 1850-1915 MHz 1710-1755 MHz |
| UL Frequency Range | 728-746 MHz 746-757 MHz 869-894 MHz 1930-1995 MHz 2110-2155 MHz |
| DL Frequency Range | Band 12 Band 13 Band 5 Band 25-2 Band 4 |
| Supported Standards | CDMA, WCDMA, GSM, EDGE, HSPA+, EVDO, LTE and all other cellular standards |
| Gain | 68 dB |
| Impedance | 50 ohm |
| Dimensions | 6 x 9.7 x 1.4 inches 152 x 246 x 36 mm |
| Weight | ≤ 5.0 lb 2.0 kg |
| FCC NOTICE | This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by FCC or a licensed wireless service provider. |
| WARNING: California's Proposition 65 | This product can expose you to chemicals including Nickel (Metallic) which is known to the State of California to cause cancer and Bisphenol A (BPA) which is known to the State of California to cause birth defects or other reproductive harm. For more information go to https://www.p65warnings.ca.gov/. |
Installing any consumer signal booster setup is fairly simple, but can be a pain. The results, however, are worth it.
You’ll need some general handyman skills but nothing too specialized. If you prefer having someone else do the job, you can also contact your local general contractor, electrician, or anyone who's installed a satellite TV dish.
-
1. Find The Best Outside Signal:
Begin by finding the best signal outside your house. This is done by walking around the perimeter of your home and either using the number of bars on your phone (ok method), smartphone apps (good method), or Field Test Mode (great method) to find the best location. Pro tip: Locating the side of your home getting the best signal is the MOST CRUCIAL step of the installation process. -
2. Install Outside Antenna
The area with the best signal is where you will mount the outside antenna. Place the antenna as high up as possible, ideally on the roof, although the fascia or gable is acceptable. It's important that the outside antenna should be on or near the edge of the roof pointing away from the house to the cell tower and NOT pointing across the roof since it may cause interference with the inside antenna. Point the outside antenna at your nearest cell tower. -
3. Connect to Amplifier
Once the outside antenna is mounted, connect the included coaxial cable to the outside antenna and to the "outside antenna" port on the amplifier. Some run cable into the attic, others prefer using the window-entry cable. It's all a matter of preference and aesthetics and where you want to locate the amplifier. Pro tip: The amplifier does all the heavy lifting for boosting signal and will get warm. Keep it in a well-ventilated area. -
4. Install Inside Antenna
Once the cable is connected to the "Outside Antenna" port of the amplifier, do the same for the "Inside Antenna" port. Some prefer having the antenna mounted on the ceiling, others prefer the wall. Again, it's all a matter of preference, and use case. If you have a panel antenna, they generally perform best on the wall, and if you have a dome antenna, they usually perform best on the ceiling. If you have multiple antennas, you will need to use a splitter to divide the cable runs, and then place each antenna where you'd like them. Pro tip: Having enough separation between the two antennas prevents oscillation. Make sure there is at least 20 feet vertical or 50 feet horizontal distance between the two. -
5. Power on
Plug in the power supply to the Amplifier and to the wall outlet. The amplifier will sync up and if you see all green lights, then green means GO! Check to see near the inside antenna how much better signal you're getting. Pro tip: Any post-installation adjustments like relocating the outside antenna will require rebooting the amplifier. Simply unplug the power supply for 5-10 seconds and replug to reboot the system. -
Technical Support & Troubleshooting
If you need help setting up your amplifier system and troubleshooting support: our trained product specialists can assist. Just call us at 1-800-470-6777 or email sales@signalboosters.com